国产在视频线精品视频_国产成人精品无码一区二区_国内少妇人妻丰满AV_久久婷婷综合色丁香五月

鈦陽極旋流電解時需注意的幾點安全事項！

發布時間：2024-01-30 13:49:01 丨 瀏覽次數：

　　鈦陽極旋流電解時為確保操作安全，減輕其他設備被電解液腐蝕的機會，同時也是為了對陰極銅進行初步淋洗，建議在打開（或處理）電解槽之前沖洗電解槽。除此之外，在產品采集時，建議電解槽處于“充滿”狀態，這樣在從電解槽中取出陰極產品時，可以起到額外的“潤滑”作用。一般說來，電解槽在下述情況下需要進行沖洗： 產品采集時電解槽維修前旋流電解裝置在正常情況下的產品采集是斷電的情況下進行的。因此一般采用沖洗水對模塊進行沖洗。

　　開啟沖洗水閥門，使“干凈”的水通過管道流進電解槽模塊。電解槽的沖洗取決于沖洗水流經電解裝置對電解液進行的置換。因此，剛開始沖洗時，電解液仍然存在于模塊中，當電解液置換完成后，溶液管出口連通到沖洗液儲罐。一個較好的方案是通過各排電解槽下部的排放閥放空電解液，再進行沖洗，這樣可以減輕沖洗水與電解液的交叉污染。在開始向電解槽中重新通入電解液前，沖洗液要排放掉。重新通入電解液的操作程序與上述過程相反。

　　同時，旋流電解裝置開停車時也要注意以下事項：

　　1)啟動變頻器和溶液泵，建立通過電解模塊的流量，確定槽體空氣已經排空

　　2)按工藝參數，檢查流量，調整變頻器頻率，將流量調整到設定值

　　3)打開整流裝置

　　4)調整整流裝置到設定值（整流裝置處理恒流狀態）